Hi-Lo camper travel trailer forum

Hi-Lo camper travel trailer forum (https://www.hilotrailerforum.com/)
-   General Hi-Lo camper discussion (https://www.hilotrailerforum.com/f17/)
-   -   Lowering problem solved...Yahoo (https://www.hilotrailerforum.com/f17/lowering-problem-solved-yahoo-2906/)

raysnuffer 01-24-2013 10:39 AM

Lowering problem solved...Yahoo
 
Hello all,

Have a 1908 Towlite that just started not lowering without playing with the switch several times. And yes, I did pull the lock cable as I hit the switch.

Turns out the Electric relief valve was loose. I looked at the Monarch pump and followed the yellow wire to the switch. The valve is bolted to the pump so I used a cresent wrench to tighten it.

This site pointed me to the electric valve which was very helpful.

Hope this helps somebody in the forum.

Thanks
Raysnuffer

RichR 01-24-2013 11:53 AM

That can be valuable information for us to keep in mind.

Great news! I love stories with happy endings!! :)

raysnuffer 01-25-2013 11:05 AM

It lowers great !!!
 
Thanks Richr,

I was ecstatic that it worked....I was envisioning hundreds of dollars fixing the pump :)

davidc 01-25-2013 11:59 AM

Quote:

Originally Posted by raysnuffer (Post 17296)
Thanks Richr,

I was ecstatic that it worked....I was envisioning hundreds of dollars fixing the pump :)

Just out of curiosity... how much is it to rebuild one of these pumps? It's just a "simple" pump after all and was probably designed/built with "off the shelf" parts... Pumps to build pressure and a valve to release that pressure.... not as complicated as a hydraulic setup using pressure in both directions...

RichR 01-25-2013 04:15 PM

Quote:

Originally Posted by davidc (Post 17297)
Just out of curiosity... how much is it to rebuild one of these pumps? It's just a "simple" pump after all and was probably designed/built with "off the shelf" parts... Pumps to build pressure and a valve to release that pressure.... not as complicated as a hydraulic setup using pressure in both directions...

I think someone posted about that not too long ago. Maybe a search will get you there or even maybe the poster will step up and fill you in here.

davidc 01-26-2013 11:32 AM

Quote:

Originally Posted by RichR (Post 17307)
I think someone posted about that not too long ago. Maybe a search will get you there or even maybe the poster will step up and fill you in here.

Yup 80 bucks - A quite a bit away from "a couple hundred"... Like I figured, these aren't that complicated a pump, after all, it only makes pressure one way.

raysnuffer 01-26-2013 12:01 PM

Rebuild Monarch lift pump...
 
Thanks David C for the price to rebuild pump. Just for the future, is that rebuild a do it yourselfer or is that the price having it done by a pro ?? I would not be able to do it myself and RV places here charge 90.00 an hour. I suspect they would not take on the project for less than 3 hours which is a long way from 80.00.


I found the pump on Ebay for 349.00 plus shipping for those that may need a new one.

Monarch Hydraulic Pump 6 Qt Reservoir 12 Volt | eBay

Ray

davidc 01-26-2013 12:10 PM

It was from this thread https://www.hilotrailerforum.com/f22/...efurbish-2248/

And an RV place is the last place you should take it, they most likely would just "shop" it out to a hydraulic shop... You would simply take it to a hydraulic shop, but as stated in the thread, he was able to find a shop that was "familiar" with the pump used... not that it's necessary, any shop should be able to rebuild it, but it would be nice to find one that knew what they were...

An RV shop is not your only source just because it's an RV...

RichR 01-26-2013 01:44 PM

Quote:

Originally Posted by davidc (Post 17312)
Yup 80 bucks - A quite a bit away from "a couple hundred"... Like I figured, these aren't that complicated a pump, after all, it only makes pressure one way.

I believe the $80 was to have the cylinder repaired, if I read it correctly. The pumps are similar to snow plow lift pumps, I would imagine that hydraulic shops would work on those.

edward lansing 01-27-2013 08:57 AM

Lowering Problem- Hydraulic Cylinder
 
I went thru a removal, repair, and re-installation of the hydraulic cylinder about a year ago. Here is what I learned.

1. The Hydraulic Cylinder is a "plain Jane" type used on all kinds of equipment. Just look at any front end loader, garbage truck, fork lift etc.

2. It is high pressure and you need the right parts. No junk.

3. Any auto repair shop, hydraulic equipment shop, or hydraulic equipment shop can handle. There are seals, wipers, etc involved.

4. You will pay the going shop rate, say $60 to $80 per hour. One or two hours. I had to have some lathe work done on a bent shaft so I spent about $ 150.

5. Removal and re-install not too bad, just poor working conditions under the trailer. It is just like working on a auto starter. It is buried and hard to get at.

5. CAUTION: High pressure involved, Coul be thousand psi so do it right.

raysnuffer 01-27-2013 03:10 PM

Remove/reinstall question
 
Thanks for the info Edward. When you took out and put it back, did you have to bleed the hoses to get the air out and refill the tank or were you able to plug the the hose as you removed the pump to prevent much fluid from draining out ???

Thanks
Ray

PopRichie77 01-27-2013 05:53 PM

The system on both of mine is self bleeding, just fill tank in down position to proper level and run up an down a couple times, check fill level again in down position and you are good to go.

edward lansing 01-27-2013 05:56 PM

Hydraulic Cylinder
 
Right ON! Capped the hoses on removal. On installation just fill reservoir, cycle a few times and it self bleeds itself.

RCREYES 01-27-2013 09:34 PM

If I remember correctly, a replacement hydraulic pump is available through Northern Tool.

raysnuffer 01-28-2013 01:22 PM

Sounds like fun !!!
 
Thanks guys for the "self bleeding" info on the lift pump... It almost makes me want to try it... (hopefully not soon) :rolleyes:

And good info from RCREYES about another source for the pump if we need a new one. Its good to know that whatever parts we Hilo'ers need can still be bought.

Ray


All times are GMT -5. The time now is 05:19 PM.

Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
HiLoTrailerForum.com Copyright 2010