Journey with Confidence RV GPS App RV Trip Planner RV LIFE Campground Reviews RV Maintenance Take a Speed Test Free 7 Day Trial ×
 
 


General Hi-Lo camper discussion The perfect place to discuss your Hi-Lo camper
Reply
 
Thread Tools Search this Thread Display Modes
 
Old 05-17-2015, 06:50 PM   #1
Member
 
bshetts's Avatar
 
Join Date: Jun 2014
Location: Michigan
Posts: 23
Default We Did It! (I hope)

Last week my buddy and I replaced the bulb seal on my 19TL. Quite a learning experience. Some mistakes were made but we managed to get it replaced and the two halves back together and hydraulics functioning. We blocked the front end using 4x4s with 2x4s attached at the top and used a lift truck with a pallet on the forks to support/lift the back end of the top half. Replaced all 6 guide blocks as well. Took around 16 hours total because we had to re-separate the halves as we tore the seal in 3 spots on the guide rails the first time we ran it down. After re-separating the halves and replacing the seal where it had torn we took great care to be sure it did not catch on the guide rails on the way down and adjusted the cables to make sure the seal doesn't go above the tops of the guide rails when raised. Live and learn!
__________________

bshetts is offline   Reply With Quote
Old 05-18-2015, 03:18 PM   #2
Senior Member
 
Join Date: Mar 2011
Location: Riverside County, CA
Posts: 691
Default

Quote:
Originally Posted by bshetts View Post
Last week my buddy and I replaced the bulb seal on my 19TL. Quite a learning experience. Some mistakes were made but we managed to get it replaced and the two halves back together and hydraulics functioning. We blocked the front end using 4x4s with 2x4s attached at the top and used a lift truck with a pallet on the forks to support/lift the back end of the top half. Replaced all 6 guide blocks as well. Took around 16 hours total because we had to re-separate the halves as we tore the seal in 3 spots on the guide rails the first time we ran it down. After re-separating the halves and replacing the seal where it had torn we took great care to be sure it did not catch on the guide rails on the way down and adjusted the cables to make sure the seal doesn't go above the tops of the guide rails when raised. Live and learn!
Can't get a clear picture of what you did with the front end, but it sounds like a clever way to separate the top and bottom.
__________________

__________________
Fantastic Wife
2005 Toyota Tundra V-8 4.7L
2705T Tow Lite
1999 21T Tow Lite
Garry is offline   Reply With Quote
Old 05-18-2015, 08:18 PM   #3
sam
Senior Member
 
Join Date: Mar 2010
Location: Niagara Falls,NY
Posts: 4,051
Default seal replacement

Just think of all the fun you had and the $ you saved. We had to redo a small part of our seal replacement as we didn't use heavy enough metal. The metal curled up and fell out. It is fixed properly now.
sam is offline   Reply With Quote
Old 05-19-2015, 01:18 PM   #4
Member
 
bshetts's Avatar
 
Join Date: Jun 2014
Location: Michigan
Posts: 23
Default Bulb Seal Replacement

Maybe these will help!
Attached Images
File Type: jpg 20150509_094929.jpg (131.2 KB, 30 views)
File Type: jpg 20150509_094941.jpg (101.9 KB, 31 views)
File Type: jpg 20150509_094903.jpg (185.9 KB, 30 views)
File Type: jpg 20150509_094851.jpg (231.2 KB, 30 views)
bshetts is offline   Reply With Quote
Old 05-19-2015, 01:31 PM   #5
Member
 
bshetts's Avatar
 
Join Date: Jun 2014
Location: Michigan
Posts: 23
Default A few more shots!

We did a few things differently then the Sam Shields instructions indicated. There was plenty of slack in the wiring so we didn't cut wires. We detached the lift cables underneath the trailer instead of from the top half. We used galvanized steel flashing and a pneumatic stapler to install the new seal. We also used shorter 2x4s and went across the corners instead across the entire trailer to separate the halves. This made it easier to remove the old seal and install the new one. We didn't have to work around/reach across the 2x4s to install the seal on the front and back walls. All in all, I learned a lot about my trailer!
Attached Images
File Type: jpg 20150509_102412.jpg (171.3 KB, 38 views)
File Type: jpg 20150509_102404.jpg (210.6 KB, 38 views)
File Type: jpg 20150509_103529.jpg (211.4 KB, 43 views)
File Type: jpg 20150509_103538.jpg (219.9 KB, 43 views)
bshetts is offline   Reply With Quote
Old 05-19-2015, 02:03 PM   #6
Senior Member
 
Join Date: Mar 2011
Location: Riverside County, CA
Posts: 691
Default

Quote:
Originally Posted by bshetts View Post
We did a few things differently then the Sam Shields instructions indicated. There was plenty of slack in the wiring so we didn't cut wires. We detached the lift cables underneath the trailer instead of from the top half. We used galvanized steel flashing and a pneumatic stapler to install the new seal. We also used shorter 2x4s and went across the corners instead across the entire trailer to separate the halves. This made it easier to remove the old seal and install the new one. We didn't have to work around/reach across the 2x4s to install the seal on the front and back walls. All in all, I learned a lot about my trailer!
Thanks for the photos, got a clear picture now.
__________________
Fantastic Wife
2005 Toyota Tundra V-8 4.7L
2705T Tow Lite
1999 21T Tow Lite
Garry is offline   Reply With Quote
Old 05-19-2015, 02:32 PM   #7
Site Team
 
Treeclimber's Avatar
 
Join Date: Feb 2015
Location: SWFL Bonita Springs/Andrews, NC
Posts: 1,264
Default

Lucky to have a forklift in your toolbox!
Tree
__________________
Treeclimber
2703 Tow Lite
2002 Escalade
Bonita Springs, Fl. &
Andrews, NC
Treeclimber is offline   Reply With Quote
Old 03-04-2016, 09:23 AM   #8
Member
 
Join Date: Jan 2016
Location: Frankfort, OH
Posts: 21
Default

I going to try this next weekend. Great pictures.
Terry1221 is offline   Reply With Quote
Old 03-04-2016, 11:21 AM   #9
Senior Member
 
hilltool's Avatar
 
Join Date: Feb 2012
Location: Wisconsin
Posts: 1,256
Default

Impressive- thanks.

Rick
__________________

__________________
2201 TL

2010 Nissan Titan king cab SE
4x4
hilltool is offline   Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


» Featured Campgrounds

Reviews provided by

Powered by vBadvanced CMPS v3.2.3
Disclaimer:

This website is not affiliated with or endorsed by Hi-Lo Trailers Worldwide or any of its affiliates. This is an independent, unofficial site.


All times are GMT -5. The time now is 12:32 AM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
HiLoTrailerForum.com Copyright 2010
×