Journey with Confidence RV GPS App RV Trip Planner RV LIFE Campground Reviews RV Maintenance Take a Speed Test Free 7 Day Trial ×
 
 


Exterior Roof, doors, windows, awnings, etc
Reply
 
Thread Tools Search this Thread Display Modes
 
Old 12-04-2017, 12:53 PM   #1
Senior Member
 
Join Date: Oct 2017
Location: cobbo
Posts: 239
Default Aluminum Roof Holes

Posted this in another thread, but needs it's own.

My used camper has what I thought was a minor water damage spot. I keep taking more ceiling out. I have about 1/4 of the ceiling out.

Found the leak, it is holes in the actual roof, like decayed spots. Ceiling is wet, but not rotted. Pulling out all ceiling below the foam and will install new ceiling in front half. Metal frame is very rusted in spots and in spots I can punch through with the putty knife. Ideally I would pull entire roof off, new metal framing, and redo it all, but that is more than I want to put into this used camper of 20 years. Plan to fix the minimum.

What is the best fix for these holes? Most of the roof does not have them, but will eventually I am sure. Rubber coating? I am thinking maybe just lay new aluminum sheets over the roof at the bad half. Best glue?


Patched with duct tape for now.


Pictured next to roll of tape.


Holes are the black spots.
I assume this is an aluminum roof. Not steel???
__________________

__________________
1997 22L
Renovation complete!
marininn is offline   Reply With Quote
Old 12-04-2017, 03:32 PM   #2
Site Team
 
JackandJanet's Avatar
 
Join Date: Jul 2010
Location: Pine, AZ
Posts: 4,524
Default

That appears to be galvanic corrosion, caused by contact between dissimilar metals. I think you'll find steel screws or nails underneath the corroded spots? I've not had to repair any of these holes in my roof but others have used Bondo to fill them. Then, since you have a painted aluminum roof, I'd coat it with two coats of white elastomeric roofing paint.

- Jack
__________________

__________________
Hi-Lo 1707T - Tire Minder TPMS on Tow Vehicle and Trailer, 300W Solar Battery Charger, Equal-i-zer WDH, Progressive Dynamics Converter, Fan-Tastic Fan, LiFePO4 battery 12V DC Electrical System
2014 F150 Platinum 4x4 3.5L EcoBoost SCrew
JackandJanet is online now   Reply With Quote
Old 12-04-2017, 04:27 PM   #3
Senior Member
 
Join Date: Oct 2017
Location: cobbo
Posts: 239
Default

There is the square steel tubing glued directly to the roof, but that might be insulated enough with the glue between, assuming there is glue. However, the holes are not along the steel frame area, but are all over. Mostly concentrated in a small area. I am thinking maybe it was parked under a low-touching branch at one point, keeping the roof wet.
I am wondering if these corroded from the inside or from the outside.

Possible the holes are not the source of the water originally.

Has anyone seen water come in at the wall/roof corner and run uphill along the slanted roof? That would be called capillary movement or something…. Which would mean possible leak at the top of wall.
But then how would it get from ceiling to roof???

Main question is still, what is best to fix? A paint on rubber coating?

Bondo, or maybe fiberglass epoxy I am thinking also of possible hole patches before the coating.
__________________
1997 22L
Renovation complete!
marininn is offline   Reply With Quote
Old 12-04-2017, 05:50 PM   #4
Site Team
 
Treeclimber's Avatar
 
Join Date: Feb 2015
Location: SWFL Bonita Springs/Andrews, NC
Posts: 1,264
Default

As a corrosion control team member in aviation, I can tell you this: galvanic (dissimilar metal) does NOT require an actual metal to metal contact. As the trailer is used, humidity turns to condensation. The moisture is everywhere, trapped in the ceiling, this causes a tiny electrical current, just like a battery. This moisture does not have to "flow", it's just there. Therefore, the pinholes are formed from the INSIDE and WILL continue to get larger, regardless of what is done to the outside, short of cutting out each affected area, patching and sealing.
I ground mine with a wire wheel with a vacuum attached, used a magnet after, patched and Eatherbonded over it, and told the buyer what I had done.
One last note, An RV dealer/repair shop in GA is said to have replaced an aluminum roof with a rubber roof. I'm sure it can be done.
Tree
__________________
Treeclimber
2703 Tow Lite
2002 Escalade
Bonita Springs, Fl. &
Andrews, NC
Treeclimber is offline   Reply With Quote
Old 12-04-2017, 05:54 PM   #5
Site Team
 
Treeclimber's Avatar
 
Join Date: Feb 2015
Location: SWFL Bonita Springs/Andrews, NC
Posts: 1,264
Default

OOPS! Sorry, that was Eternabond tape
__________________
Treeclimber
2703 Tow Lite
2002 Escalade
Bonita Springs, Fl. &
Andrews, NC
Treeclimber is offline   Reply With Quote
Old 12-04-2017, 06:03 PM   #6
Senior Member
 
garyk52's Avatar
 
Join Date: Oct 2011
Location: Berwick. Pa
Posts: 343
Default

I had the same problem when I repaired mine in 2012. Holes in the aluminum scattered throughout the right rear quarter of the camper (passenger side). From what I could tell the roof is made of from outside in, aluminum skin, 1/8 inch sheeting, One inch styrofoam, and the 1/8 inch ceiling panels. I repaired mine by scabbing right angle metal on the 1 inch tube where needed. Then I bought a roll of eternabond tape and from the top put patches on all the holes. Then I coated it with 2 coats of white elastomeric paint. Summer of 2017 five years later I could see where the roof was starting to form some rust spots so out came the eternabond tape and then 2 more coats of the elastomeric paint. I caught all the rust spots before they had time to cause a problem and in the summer of 2018 I'm going to put 2 more coats on. Here is the video I made when I repaired mine in 2012 if your interested.
__________________
Cheers
Garyk52
DW Judy

96 24' Hi-Lo Funchaser, (99 Aliner Sofabed Sold 6/9/18)
06 Toyota Tundra SR5 Access Cab 4X4 36,000 miles and counting
garyk52 is offline   Reply With Quote
Old 12-04-2017, 06:37 PM   #7
Senior Member
 
Join Date: Oct 2017
Location: cobbo
Posts: 239
Default

Nice vid and renno.
How do the cabinets bolt in? I can see the screws around the door opening, but others are covered going to the wall.
What adhesive are you using to glue the foam? I see a big bucket.
Liquid Nails will melt the foam, as LN heats up when curing, but I guess you got enough bonding somewhere in there for it to work.

So, galvanic corrosion started because of humidity inside? The roof is aluminum, right, what is the magnet for, the frame?

I was hoping the foam bonded to the roof directly, but sounds like there is another plywood bonded to roof. So, the plywood bonded to the roof is wet and will continue to corode the roof?
It won't dry behind the foam, so the foam needs to come out, but will the plywood then dry enough to leave it or needs to come out? I have a heater in there helping dry things out right now. I am worried about tearing the roof if I try to remove the plywood that is glued to it.
__________________
1997 22L
Renovation complete!
marininn is offline   Reply With Quote
Old 12-04-2017, 06:57 PM   #8
Senior Member
 
garyk52's Avatar
 
Join Date: Oct 2011
Location: Berwick. Pa
Posts: 343
Default

Marininn, The cabinets have a false bottom in them. Inside you will see staples holding the bottom down. Liquid Nails will not melt the foam as it isn't made from the same stuff it was made from years ago. I used more than 20 tubes of Liquid Nails. It doens't stick as quick as the stuff that was made 30 years ago, but it also doesn't smell (low VOC). You may find the plywood between the aluminum and the foam will have delaminated if not it will dry. Anything that is rotten needs to come out because of possible mold. BTW just tear the plywood out that is loose.
__________________
Cheers
Garyk52
DW Judy

96 24' Hi-Lo Funchaser, (99 Aliner Sofabed Sold 6/9/18)
06 Toyota Tundra SR5 Access Cab 4X4 36,000 miles and counting
garyk52 is offline   Reply With Quote
Old 12-05-2017, 01:05 PM   #9
Senior Member
 
Join Date: Oct 2017
Location: cobbo
Posts: 239
Default

Thanks, I see the bolts on cabinet now.

I pulled all the styrofoam out of the ceiling where it was wet. Fortunately it is only the front 1/4 needing work. I still need to get a bit of it under the to-be-removed cabinets, but hoping it is just a few inches.

Neck tired from looking up, so taking break…

In year 2001 Liquid Nails would melt the the foam, now you are saying it will not. Is the cheap $1.44 "construction adhesive" just as good for foam?

I am also considering using Glidden's Gripper paint as it is some sort of styrofoam based paint, and works to stick it together well, at least for other projects Ive read about.
Hoping someone has tried this for ceilings.

garyk52, why did the holes come back? Was moisture still getting up there?
How did the rubber do over time sticking to the eternal tape? I have some tape like that I planned to use to tape solar panels on, but can use the extra to tape my 28 holes.
Gary, you had "carpet" bucket there, was that the glue for ceiling?
How are the angle irons holding up? Mine is not cracked, but very thin and I pushed a hole in it in a place. Worried to drill a hole like u did to bolt in angle iron. The factory holes for the wiring, too big for one, and stupid for factory to put a hole through the vertical part of tube two. I am thinking maybe gluing it on. I have a gap above, probably since metal frame droops now, and can put one angle above the frame, that might help to hold it all.
Gary, you build wooden rectangle frames, what is purpose of those?

If I wanted to spend $1k and had a barn to work under and more time maybe I would just re-do the entire roof and make it right. I just need it to stay dry and look nice.
My theory is that the couple living in the camper 6 months right before I bought it exhaled moisture, and the one on the bunk had head under where the water damage is. Seems like moisture would go everywhere,but this is just a thought why damage is just in one spot. Maybe they showered and didnt vent or let the water dry before closing it up. I want to make sure this does not happen again… Maybe rain water entered at the metal seam, as there is a hole at the seam too.


Wall with all but the last ply stuck to wall. Rusty metal.


Ceiling, I have since pulled out the foam and most of the plywood glued to the roof. Leaving the plys that are not buckled away. I think they will dry and be fine.
More pics to come…
__________________
1997 22L
Renovation complete!
marininn is offline   Reply With Quote
Old 12-05-2017, 02:50 PM   #10
Member
 
Join Date: May 2017
Location: Oklahoma
Posts: 68
Default

eternabond tape over seams aluminum Patches on big holes and elastomeric paint
MrEd HiLo is offline   Reply With Quote
Old 12-05-2017, 02:52 PM   #11
Member
 
Join Date: May 2017
Location: Oklahoma
Posts: 68
Default

Check out mine 1977 Hi-Lo went thru what your going thru
MrEd HiLo is offline   Reply With Quote
Old 12-05-2017, 07:01 PM   #12
Senior Member
 
Join Date: Oct 2017
Location: cobbo
Posts: 239
Default

MrEd , looks like you just did a complete rebuild. Im hoping to do a few fixes.
__________________
1997 22L
Renovation complete!
marininn is offline   Reply With Quote
Old 12-06-2017, 09:57 AM   #13
Senior Member
 
garyk52's Avatar
 
Join Date: Oct 2011
Location: Berwick. Pa
Posts: 343
Default

Marininn, I took Sams advice and just used regular Liquid Nails (yes construction adhesive). I bought mine wherever it was the cheapest (Walmart), I probably used more than I needed, however I don't have any sidewall or ceiling panels coming loose in 5 years.

Those are new holes that started to come thru, after all you're talking about a 21 year old camper aluminum roof. I'm sure it's going to be a never ending process keeping up with them. The camper isn't showing any moisture on the inside that I can see. No probem with the elastomeric paint over the eternabond tape, sticks well use a 3/4" nap roller to put the paint on. Mine uses about 1 gallon per coat.

Started with carpet adhesive but changed to Liquid Nails. The carpet adhesive was drying hard and figured that would be a problem over time.

Angle Iron is working great, drilled holes in the 1" tube and bolted the angle iron to it. Was going to weld it, but was afraid I would burn the camper down. Scab 2 pieces of angle to each area you need to reinforce. Can you make the angles long enough to get to solid metal? Then glue and bolt.

The wooden rectangle frames are for gluing and stapling 1/8 inch luan where I removed the old ceiling and foam before replacing with new, then sheeted the whole ceiling with new painted panels. I don't know how much time or money you want to invest, but I took all the vinyl from the ceiling panels before I glued the new panels up. I found a few wet spots when I took the vinyl off and then ran a fan a couple of days to make sure the whole ceiling was dry. I now have 2 layers of 1/8" luan (plywood) on the ceiling.

You have the same problem I had, age of the camper and lack of maintanence and probably stored outside in the weather. I can't complain thou, I bought mine for a dollar and have less than $2000.00 in a camper that costs $30000.00 when new. This will last me the rest of my camping days.
__________________
Cheers
Garyk52
DW Judy

96 24' Hi-Lo Funchaser, (99 Aliner Sofabed Sold 6/9/18)
06 Toyota Tundra SR5 Access Cab 4X4 36,000 miles and counting
garyk52 is offline   Reply With Quote
Old 12-06-2017, 11:15 AM   #14
Senior Member
 
Join Date: Oct 2017
Location: cobbo
Posts: 239
Default

That's good to hear.


did the carpet adhesive dry faster? I think Im fine with it being harder, think I like that better as it would be more like a surfboard, hard and with structural integrity. With the steel frame compromised it needs help. Even if it cracks here and there, so what, it will still hold the pieces together…

I had some left over cheap construction adhesive *. Put some on the old foam, and also glued a piece of the plywood to it. in garage, maybe cold, but is what camper will be in December too, it did not cure overnight. The glue stuck great where was just exposed glue and dried, but under the wood was still wet, and popped off easily, so if I do that with panels it will take a week to dry…
So, I think the faster drying $4 stuff instead.

It rained yesterday, found there were many, many more holes than I could see. Covered in plastic now.

If you are reading this and think your camper is fine: it is not. Re-caulk everything! Lay rubber coating on the old roof. Be paranoid.

$2500 for this camper, still a good deal as the next ones are over $5k used and no guarantee they are perfect, so a few hundred in repairs made saving $2k not a bad deal. $1 would have been a lot better.

* unrelated - I did a gettho floor repair. The OSB floor at the rear was exposed completely to the open. The rear bumper shroud separated and let water in, another weakness in design. The OSB rotted out, but only the interior. The bottom of the OSB, open to air was fine, and the top was fine, or the top being the linoleum floor. I gutted out the rot and squirted in some Liquid Nails. Should dry hard and this area was not really structural so should be the end of it. Im sure there are other problems more pressing than floor issues in unseen places.. lol.
Anyway, used the cheap adhesive on last part. I had about 8 bottles of good LN and two of cheap. The cheap stuff is not drying nearly as fast.
__________________
1997 22L
Renovation complete!
marininn is offline   Reply With Quote
Old 12-07-2017, 12:46 AM   #15
sam
Senior Member
 
Join Date: Mar 2010
Location: Niagara Falls,NY
Posts: 4,048
Default Repairs

Garyk52 did a nice write up for you. Clarification..Used Heavy Duty liquid nails. The regular strength didn't hold up. We repaired in the cold weather and kept the furnice running at 60*. Long Johns needed. Every 2to3 days we had to refill the propane. Our saving grace was that we live close to the Indian Reservation and could get cheap tax free propane.
sam is offline   Reply With Quote
Old 12-07-2017, 08:38 AM   #16
Senior Member
 
Join Date: Oct 2017
Location: cobbo
Posts: 239
Default

Sam, every 2-3 days? How many days did it need to cure?
__________________
1997 22L
Renovation complete!
marininn is offline   Reply With Quote
Old 12-07-2017, 12:07 PM   #17
Senior Member
 
Join Date: Oct 2017
Location: cobbo
Posts: 239
Default

More photos os deconstruction. I plan to put angle iron down the length of the roofline inside to help lift the sagging door, and this will add strength to the ceiling tubing. Going to put a plate over the door, plate recycled from kick plate on interior school door.
I may put some square tubing at an angle around the door to give strength also.
Will put in 1x3 wood strip inside walls in places also.
Ceiling will get the crossmember such as over bathroom wall, this should add strength to rusty tubing holding up AC.

Yes, I need to do a complete roof redo. Not going to happen this cycle, maybe next year when Im not remodeling an entire camper at the same time…



Stripped down. I plan to take out last layer of ply later, not during the rain.


Frame not any good.


Door exposed, just incase anyone wonders whats back there…
I took screws out of the green padding, but the pad will not come off. Is it glued or stapled somewhere? I know how these builders love staples. Door will have to be removed.


This is what holds the bunk up.
__________________
1997 22L
Renovation complete!
marininn is offline   Reply With Quote
Old 12-07-2017, 03:28 PM   #18
Senior Member
 
garyk52's Avatar
 
Join Date: Oct 2011
Location: Berwick. Pa
Posts: 343
Default

I took screws out of the green padding, but the pad will not come off. Is it glued or stapled somewhere?

Dig around in those holes and you will find 2 more long screws holding the head bumper on. Don't remember if they are phillips head or robertson screws.

Top half of door comes off by taking the rubber (plastic) trim off the door on the outside and removing screws.

The bunk from mine hangs in my shed in a mattress bag. Only 2 of us, won't reinstall unless I decide to sell the camper.
__________________
Cheers
Garyk52
DW Judy

96 24' Hi-Lo Funchaser, (99 Aliner Sofabed Sold 6/9/18)
06 Toyota Tundra SR5 Access Cab 4X4 36,000 miles and counting
garyk52 is offline   Reply With Quote
Old 12-07-2017, 07:57 PM   #19
sam
Senior Member
 
Join Date: Mar 2010
Location: Niagara Falls,NY
Posts: 4,048
Default Repairs

We also used the heat to make us more comfortable while we were working. I think you need to fix your roof with a total tearout before you fix the walls. GaryK52 correct me if I am wrong. I would hate to see you fix the walls and then have them get trashed/wet because the roof isn't fixed. Gary said he spent all his free time for an entire summer working on his HiLo.
sam is offline   Reply With Quote
Old 12-07-2017, 10:38 PM   #20
Senior Member
 
Join Date: Oct 2017
Location: cobbo
Posts: 239
Default

I will stop the water with a rubber paint-on coating. If the corrosion continues in the roof, then when I have time I can tear the roof off completely. There is no aluminum in the walls to go bad, and the water will be stopped so he walls should be good to go.
Yes, the issue of galvanic corrosion will remain, and Im sure there is moisture somewhere in the untouched realms of the ceiling. I can't replace it all now as I am on a deadline. I will be using this for work as I travel all over. Im not retired, don't have as much spare time as I need. Camping/traveling starts in January, absolute deadline is end of January.
__________________

__________________
1997 22L
Renovation complete!
marininn is offline   Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


» Featured Campgrounds

Reviews provided by

Powered by vBadvanced CMPS v3.2.3
Disclaimer:

This website is not affiliated with or endorsed by Hi-Lo Trailers Worldwide or any of its affiliates. This is an independent, unofficial site.


All times are GMT -5. The time now is 12:23 PM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
HiLoTrailerForum.com Copyright 2010
×