Journey with Confidence RV GPS App RV Trip Planner RV LIFE Campground Reviews RV Maintenance Take a Speed Test Free 7 Day Trial ×
 
 


New Member Intros Say Hello! Tell us a little about yourself and your camper; we're fairly friendly :)
Reply
 
Thread Tools Search this Thread Display Modes
 
Old 08-07-2015, 09:26 PM   #1
Member
 
Join Date: Aug 2015
Location: Kalispell, MT
Posts: 3
Default 2004 24' Towlite Hi-Lo retracts unevenly

I have had my Hi-Lo for 2 years and all has worked very well. Upon retraction a week ago, the front end receded faster than the rear and the top wedged, binding about half way down. I raised it and it again went up smoothly, but on retraction, the same thing happened. Everything was working perfectly before and I have no reason to suspect a broken cable (it goes back up to full extension properly).

Is it likely the front cables stretched? Can the cables be adjusted? If I have to take it to a trailer repair lot, is it safe to pull it 10 miles in the "half-up" position? I know one should not transport the trailer in the up position if possible. Or would it be better to transport the trailer to a trailer repair shop 10 miles away in the "fully up and locked" position? Or could the hydraulic piston be "hanging up" on retraction somehow?

Anyone have an answer? I would appreciate the help because I am a real novice at trailers (been a backpack camper the last 50 years). As for novice -- don't believe me? You should see me backing the thing! grizbizusa in Montana.
__________________

grizbizusa is offline   Reply With Quote
Old 08-07-2015, 10:44 PM   #2
Site Team
 
JackandJanet's Avatar
 
Join Date: Jul 2010
Location: Pine, AZ
Posts: 4,527
Default

It sounds like the front cables may have stretched and, yes, they can be adjusted. The adjusting bolts are on the left side of the trailer in front of the wheel. There are four of them. The procedure is in the owners manual and you should be able to find one that's close to your model year in the library: Hi-Lo Owners Manual - Hi-Lo camper travel trailer forum It will tell you to support the top on four equal length 2x4s and will tell you which nuts to turn. Don't overdo it - shorten them just enough to correct the problem.

- Jack
__________________

__________________
Hi-Lo 1707T - Tire Minder TPMS on Tow Vehicle and Trailer, 300W Solar Battery Charger, Equal-i-zer WDH, Progressive Dynamics Converter, Fan-Tastic Fan, LiFePO4 battery 12V DC Electrical System
2014 F150 Platinum 4x4 3.5L EcoBoost SCrew
JackandJanet is online now   Reply With Quote
Old 08-08-2015, 07:16 AM   #3
Moderator
 
RichR's Avatar
 
Join Date: Feb 2010
Location: NW PA
Posts: 3,386
Default

Before you do anything check to make sure the side vertical rails and the guide blocks are engaged with each other. The guide blocks are on the inside edge of the upper section and the rails are on the lower section.The blocks run on the rails to keep the upper and lower halves aligned. If those jump the track or are broken binding could be possible. When you say the top goes up okay and stops in its normal position I would be less suspicious of the cables being stretched. I would crawl under the trailer and see if the all the cables are on the pulleys and the pulleys are unbroken.
__________________
My Great Wife Joyce
2018 Jayco Jay Flight 21QB
Formerly owned 1705T and 2310H
2012 F150 4X4 SuperCrew EcoBoost w/Leer Cap
Reese WD Strait-Line Hitch
Amateur Radio K3EXU
RichR is offline   Reply With Quote
Old 08-08-2015, 09:19 AM   #4
Site Team
 
JackandJanet's Avatar
 
Join Date: Jul 2010
Location: Pine, AZ
Posts: 4,527
Default

^^^What he said^^^! (I should have thought of the guide block problem.) I suspect that's a more likely cause. Pulley problems ARE possible, but I think less likely.

- Jack
JackandJanet is online now   Reply With Quote
Old 08-08-2015, 10:10 AM   #5
Member
 
Join Date: Aug 2015
Location: Kalispell, MT
Posts: 3
Default Thank you - I'll check those ideas first.

Thanks RichR and Jackand Janet. Good ideas. Is it hard to see if the blocks are on the guide rails? Where can you see the blocks?
If I do need to take the trailer in to a shop, is it safe to pull it along for 10 miles in the "up" position?

This is a very helpful forum for a novice like me.

grizbizusa in Kalispell, MT
grizbizusa is offline   Reply With Quote
Old 08-08-2015, 02:47 PM   #6
Moderator
 
RichR's Avatar
 
Join Date: Feb 2010
Location: NW PA
Posts: 3,386
Default

Quote:
Originally Posted by grizbizusa View Post
Thanks RichR and Jackand Janet. Good ideas. Is it hard to see if the blocks are on the guide rails? Where can you see the blocks?
If I do need to take the trailer in to a shop, is it safe to pull it along for 10 miles in the "up" position?

This is a very helpful forum for a novice like me.

grizbizusa in Kalispell, MT
The blocks are located in the very bottom of the upper half. You can see them and touch them, and they are made of a hard plastic material. They work to keep the top and bottom spaced apart to prevent binding and scraping. http://hilotrailerparts.webs.com/app...s/show/2074035

Have you had the trailer sitting generally level when trying to lower it, if not that could cause binding. I assume you have already looked to see if there is something jammed in between the two halves. There has to be something hanging up somewhere.

You absolutely do not want to tow the trailer in the up position or you could risk doing major damage to the lift system.

Try lowering the trailer a bit at a time and raise it a little and repeat. And maybe prop something under the lower end to see if the high side wants to straighten out but don't try to force it.
__________________
My Great Wife Joyce
2018 Jayco Jay Flight 21QB
Formerly owned 1705T and 2310H
2012 F150 4X4 SuperCrew EcoBoost w/Leer Cap
Reese WD Strait-Line Hitch
Amateur Radio K3EXU
RichR is offline   Reply With Quote
Old 08-08-2015, 04:10 PM   #7
Junior Member
 
Join Date: Jun 2015
Location: hanover
Posts: 2
Default

did you fold up the bunk correctly
rtscrwbeagles75 is offline   Reply With Quote
Old 08-09-2015, 09:32 AM   #8
Senior Member
 
Join Date: Jul 2010
Location: central Virginia
Posts: 581
Default

If the guide blocks are OK and nothing jammed between the top and bottom halfs then check the cables to the rear of the top to see if they are binding somehow. Check for broken pulleys. If one of the cables has a bunch of broken wires and the wires have bunched up, this could cause the cable to bind at one of the pulleys.
__________________
Jim L & Faye
2805C
2003 Silvarado diesel crew cab
2017 Silvarado, crew cab 1500 6.2L gas w/ 8 speed tranny
central VA
JIM L is offline   Reply With Quote
Old 08-09-2015, 03:29 PM   #9
Member
 
Join Date: Aug 2015
Location: Kalispell, MT
Posts: 3
Default

I'm going to the storage facility tomorrow to check all of the suggestions that people have put up on the thread about my trailer. Thanks particularly for the admonition about not towing it in the "up" position -- I was pretty unsure about that anyway. Thanks and I'll post again when I know more about the situation. grizbizusa
grizbizusa is offline   Reply With Quote
Old 11-08-2015, 08:58 PM   #10
Senior Member
 
Luckydog671's Avatar
 
Join Date: Apr 2014
Location: Tehachapi Mountains, Calif.
Posts: 817
Default

Quote:
Originally Posted by RichR View Post
The blocks are located in the very bottom of the upper half. You can see them and touch them, and they are made of a hard plastic material. They work to keep the top and bottom spaced apart to prevent binding and scraping. http://hilotrailerparts.webs.com/app...s/show/2074035

Have you had the trailer sitting generally level when trying to lower it, if not that could cause binding. I assume you have already looked to see if there is something jammed in between the two halves. There has to be something hanging up somewhere.

You absolutely do not want to tow the trailer in the up position or you could risk doing major damage to the lift system.

Try lowering the trailer a bit at a time and raise it a little and repeat. And maybe prop something under the lower end to see if the high side wants to straighten out but don't try to force it.
While lubricating the guide rails this afternoon, I noticed one of my guide blocks is loose (the one near the left rear corner). I think it may be broken in half but not sure as it was hard to see up there. I was able to lower the top half just fine but am concerned about it long term. I see the link for the replacement part but how do you actually get up in there to replace the block, as it is quite tight?

Thanks,
__________________
Greg
2004 4x4 Chevy Tahoe
Former owner of a 2407T
Luckydog671 is offline   Reply With Quote
Old 11-08-2015, 09:10 PM   #11
Site Team
 
JackandJanet's Avatar
 
Join Date: Jul 2010
Location: Pine, AZ
Posts: 4,527
Default

Greg, there's a post or thread on this, but I THINK you take the guide track off (I believe all the screws are accessible with the top up) and then I think you can unscrew the guide block with a right angle screwdriver. Reverse the process to reinstall.

I'm pretty sure it can be done without raising the top completely off the lower half.

- Jack
__________________

JackandJanet is online now   Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


» Featured Campgrounds

Reviews provided by

Powered by vBadvanced CMPS v3.2.3
Disclaimer:

This website is not affiliated with or endorsed by Hi-Lo Trailers Worldwide or any of its affiliates. This is an independent, unofficial site.


All times are GMT -5. The time now is 10:45 AM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
HiLoTrailerForum.com Copyright 2010
×