Hi-Lo camper travel trailer forum

Hi-Lo camper travel trailer forum (https://www.hilotrailerforum.com/)
-   Interior (https://www.hilotrailerforum.com/f31/)
-   -   Rebuilt bed platform & new mattress (https://www.hilotrailerforum.com/f31/rebuilt-bed-platform-and-new-mattress-4315/)

Moonstruck 01-01-2015 11:17 AM

Rebuilt bed platform & new mattress
 
Well, finally finished rebuilding the bed platform and installed the new mattress on our new to us 27T. Bought a new RV short queen Parklane mattress, and boy is it comfortable. Almost forgot to mention the new heated mattress pad A couple of pictures.

https://i1160.photobucket.com/albums/...ps1aff3039.jpg

https://i1160.photobucket.com/albums/...psd4800110.jpg

Garry 01-01-2015 02:12 PM

Quote:

Originally Posted by Moonstruck (Post 28049)
Well, finally finished rebuilding the bed platform and installed the new mattress on our new to us 27T. Bought a new RV short queen Parklane mattress, and boy is it comfortable. Almost forgot to mention the new heated mattress pad A couple of pictures.

https://i1160.photobucket.com/albums/...ps1aff3039.jpg

https://i1160.photobucket.com/albums/...psd4800110.jpg

Moonstruck, In what way did you rebuild the bed platform?...reinforcement?:)

Moonstruck 01-01-2015 02:55 PM

Quote:

Originally Posted by Garry (Post 28054)
Moonstruck, In what way did you rebuild the bed platform?...reinforcement?:)

I'm not certain the platform in the trailer was even the stock arrangement. It had an inner spring mattress that looked like stock, but it was totally unsatisfactory. Also, when towing from Ocala to Tennessee the mattress was moving around all out of place.

I used nominal 3/4" plywood to build the platform. Duct tape was used on all joints and screw heads to keep from snagging the mattress. After cutting and radiusing the corners duct tape was used around the edges to give a better edge. I ordered a 16" adjustable retainer bar from an adjustable bed place. This keeps it from sliding forward off the platform. I then basically covered the platform with some rubber matting that should hold the mattress in place.

https://www.adjustablebedmart.com/retainerbars.html

Of course fitted bedding for an RV short queen is not stock. So we ordered a couple of sets of 600 count sheets and a duvet cover and shams. Picked up a couple of lamps. We will probably re-wall paper later. We are doing a few more mods along the way.

Garry 01-01-2015 05:14 PM

Quote:

Originally Posted by Moonstruck (Post 28056)
I'm not certain the platform in the trailer was even the stock arrangement. It had an inner spring mattress that looked like stock, but it was totally unsatisfactory. Also, when towing from Ocala to Tennessee the mattress was moving around all out of place.

I used nominal 3/4" plywood to build the platform. Duct tape was used on all joints and screw heads to keep from snagging the mattress. After cutting and radiusing the corners duct tape was used around the edges to give a better edge. I ordered a 16" adjustable retainer bar from an adjustable bed place. This keeps it from sliding forward off the platform. I then basically covered the platform with some rubber matting that should hold the mattress in place.

AdjustableBedMart.com

Of course fitted bedding for an RV short queen is not stock. So we ordered a couple of sets of 600 count sheets and a duvet cover and shams. Picked up a couple of lamps. We will probably re-wall paper later. We are doing a few more mods along the way.

We also have a 27T with the walk around bed and I guess our mattress is not stock as we did a 3000 mile trip in September which included some very bad roads, but we did not have any problems with the mattress moving around.:)

Moonstruck 01-01-2015 06:17 PM

Quote:

Originally Posted by Garry (Post 28059)
We also have a 27T with the walk around bed and I guess our mattress is not stock as we did a 3000 mile trip in September which included some very bad roads, but we did not have any problems with the mattress moving around.:)

I do not believe that the platform setup in ours was original. If you will pardon my French, it was a POS. I figured there was no way to put the pieces together, so totally rebuilt the supports and platform. Hopefully it will stay in place.

Did you post pictures of your 3,000 mile trip?

Don

Garry 01-02-2015 03:01 PM

Quote:

Originally Posted by Moonstruck (Post 28060)
I do not believe that the platform setup in ours was original. If you will pardon my French, it was a POS. I figured there was no way to put the pieces together, so totally rebuilt the supports and platform. Hopefully it will stay in place.

Did you post pictures of your 3,000 mile trip?

Don

Hi Don,
I thought I had posted more pictures of our trip but I could only find five posted, which was on October 24 on the thread "Visited My Hilo". On the same date?? I posted a recap of the trip.


All times are GMT -5. The time now is 11:41 PM.

Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
HiLoTrailerForum.com Copyright 2010